DDC Online direct digital controls
Circon - 200 Series  

CAC-200; IDC-200; LLC-200; PMC-201

Secondary Control Units
CAC-200, IDC-200, LLC-200, and PMC-201
Date Last Saved: 12/18/2003 10:32:19 AM

Product Name(s): CAC-200; IDC-200; LLC-200; PMC-201
Product Description: LONWORKS compatible, security, lighting, and power management controllers.
Product Application(s): CAC-200: Designed to operate card controlled doors and locking mechanisms. Compatible with a variety of card access technologies. IDC-200: Designed to monitor industry standard security devices including glass break monitors, motion detectors, door contacts, and tamper switches. Supports interface to remote dial-out alarming. LLC-200: Designed to control low voltage lighting control relays. Expandable to 48 circuits using (3) twelve circuit expansion modules. Supports lighting circuit activation based on occupancy or ambient lighting. PMC-201 monitors 4 power input signals to provide demand side management through electrical load shedding over the network (no hardware digital output signals). Maintains trend information on power usage, including average and peak demand. Performs pulse counting with four sliding-window or two fixed-window utility meters.
Point Quantity Characteristics
Analog Input (AI):
Digital Input (DI): See below Dry contact
Optical switch (PMC-201 only)
5-15vdc (PMC-201 only)
Universal Input (AI or DI):
Analog Output (AO):
Digital Output (DO): See below CAC-200: Form C Relay
12 Vdc· IDC-200: Form C Relay. 30 Vdc / 2A
LLC-200: Relay driver pulse

Universal Output (UO):
Other:
Control Unit Model #:AIDIUIDOAOUOOther
CAC-200 3 2 2 Wiegand card reader inputs
IDC-200 10 2 Keypad serial input
LLC-200 12 24
PMC-201 4
A/D Converter Resolution
8 bit
10 bit
12 bit
16 bit
Other NA
D/A Converter Resolution
6 bit
8 bit
10 bit
No Analog Output
Other NA
HOA switches provided on each output?
Note: These are also available as an add-on from 3rd party vendors.
No Not provided
Both AO and DO
DO Only
Other
Indicating status LED on each output?
No None
AO and DO
AO Only
DO Only
Other
Integral Flow Sensor?
Integral Damper Actuator?
Can controller accept occupant override from thermostat?
Can controller accept occupancy sensor input?
Expander Boards
Expansion Device Model #AIDIUIDOAOUOOther
LEM-200 Lighting Exp. Module (for LLC-200) 12 12
Network Ports, Protocol(s), and Speed(s) Supported
(Note: See 'Architecture' for network details)
(1) - LonTalkq with Echelon Free Topology Transceiver (FFT-10) to LON
External Communication Ports, Speeds and Access Devices (1) - RJ-45 to Laptop/PC @ 78 kbps LonTalk (except PMC-201)
Additional Information (Optional)
Network Accessing Capabilities via Controller
Access controller only
Access controller plus additional controllers on network segment / LAN
Access all controllers on system
No access available on this controller
Other
Controller Access Devices
Laptop/PC
Local Display Panel (controller-mounted)
Local Display Panel (zone-mounted)
Handheld Interface Device (proprietary device)
PDA (3rd-Party HID)
Zone-Based port (details below)
Other
Zone-Based Interface Access None. But see CLI-200 local display panel in Architecture form (permits viewing and changing parameters via direct connection to LON network).
Zone Interface Hardware
Zone-Mounted touchpad (thermostat or stand-alone display)
HID (proprietary device)
PDA (3rd party HID, with software)
Laptop/PC
none
Other N/A
*Note: This section covers the capabilities for accessing the controller or other parts of the network from the controller (i.e. 'bottom-up').
Standard access functionality is covered in the Architecture and Software sections.
**Does NOT include front-end OI functions. See vendor for specific functions available.
Functions Available Through Field Interface**:View ParamsChange ParamsChange
Programs/Logic
O&M SupportTAB/Cx Support
Laptop/PC
Local Display Panel (controller-mounted)
Local Display Panel (zone-mounted)
Handheld Interface Device (proprietary device)
PDA (3rd-Party HID)
Zone-Based port (details below)
Other
Microprocessor(s) Neuron 3150 chip
Clock Type
Powered, battery-backed
Battery powered
Powered, no battery backing
None
Other
Clock Synchronization One controller is defined during system configuration/setup as the reference timepiece that others synchronize to
Volatile Memory (RAM) Capacity Information not provided
Volatile Memory (RAM) Uses
RAM use unrestricted
RAM use restricted as shown below
Information Not Provided
Program Execution / Calculation storage
Data / Trends / Alarms storage
Configuration / Parameter storage
Control Programming storage
Others
Is Volatile Memory Supported By Battery? Yes
Battery Type(s) Lithium Battery
Battery Life 3 years
Backup Battery Operating Time Information not provided
Non-Volatile Memory Capacity (EEPROM/Flash)* Information not provided
Non-Volatile Memory Uses
Data / Trends / Alarms / Calculation Storage
Configuration / Parameter Storage
Control Programming Storage
Controller Operating System
Other
Additional Information
* Items in NV memory are not lost upon power or battery failure. Other types of NV memory such as EPROM, NOVROM, etc. do not directly impact system performance.
Can trend data be stored in this controller? Yes, IDC and PMC
How many total trend values can be stored? Information not provided
What is the controllers role in trending? Programming resident within controller gathers and stores trend data on-board. At set intervals, data is pulled by controller to workstation for archival.
Can controller be programmed to 'push' data to archive or are trends 'pulled' from controller?
When full, does controller automatically send up trend data, overwrite data, or stop logging data? If controller trend data buffer fills before being called by archive workstation, old data is overwritten.
Programming Method(s) Template/Menu-based configuration
Resident vs Non-Resident Program Execution All program execution is controller resident
Scheduling
Resident/Supervisory. This controller supervises the scheduling of other controllers.
Resident/Stand Alone. This controller contains its own schedule.
Non-Resident. This controller is dependent upon another controller for its schedule.
None. This controller has no scheduling features.
Other
Resident Energy Management
Energy management algorithms for this controller can be custom programmed
Pre-programmed/built-in algorithms available, and are fully editable using custom programming
Pre-Programmed/built-in with limited editing via template-based programming (PMC-201 only).
Controller is not typically used for energy management functions
Others
Specific Pre-Programmed Algorithms Available
None (custom programming only)
None (not applicable)
Optimal Start/Optimal Stop
Peak Demand Limiting/Load Shedding (PMC-201 only)
Economizer (enthalpy, dry-bulb, CO2, modulating/2-position, etc.)
Other
Additional Energy Management functions are resident at SI
Additional Programming Functions
DDC Loops (P, PI, PID) N/A
Automatic PID Tuning Feature N/A
Automatical-Dial Alarm Support No - See SMC-202 in Architecture form
Does controller perform multiple retries and buffer/store alarm until connection is made? No auto-dial alarm
Are multiple destinations possible? No auto-dial alarm
Upon controller power loss or hardware failure:
Are network communications affected? No
Is loss recognized on/by the network and alarm reported? Yes- by SMC-202
DO and AO response?
Outputs fail to a user pre-specified position
Outputs fail to a normal (unpowered) position
Outputs fail to last position
Other
Volatile memory functions?
Lost
Retained for life of backup battery
Other
Upon restoration of power does the controller:
Auto-reboot without operator intervention? Yes
Automatically reset/synchronize the clock? Yes
Update all monitored functions? Yes
Generate an alarm if backup battery is dead? No
Upon network or communications failure does controller:
Continue to operate standalone? Yes
Operate with last global settings or user-specified value? N.A.
Do broken network segments continue to communicate within the remaining segment?
(Note: May depend on proper termination of segments for higher speed networks.)
No
Does network automatically reconfigure upon restoration? No
Does network store 'loss of communications' alarm with time of event? Yes - by SMC-202
Additional Information (optional)
Self Test Diagnostics
Does controller have internal self-test diagnostics to check:
Processor failure? No
Internal hardware failure? No
Open/shortened sensor? No
Others?
 
Control Enclosure Optional
Power Supply Required
Voltage Voltage 24 Vac, 50-60Hz
VA 24 VA12 VA (PMC-201)
Surge Protection No
Underwriters Laboratories UL 916 PAZX (Energy Management)
FCC FCC Part 15, Subpart J, Level A
CE No
LonMark Certified
Yes
No
No - but LonWorks compatible
Information not provided
BACnet (BTL) Certified
Yes
No
Not submitted for testing
Information not provided
Other CSA 22.2 #205-M1983, #950-M89